Відео

I did the swapping of coils replaced #4 and the other 3 Coils as well as the spark plugs, replaced the O2 upstream sensor also it runs good now ... Check Engine light turned on again and now it has a multiple misfire , the O2 bank 1 sensor 1, and the misfire on coil 4. Yet it's running normal no hiccups?

Thank you for the info and video!! I bought a 2018 Nissan Altima with 70k miles. Should I change everything like you did? Or drain and fill? Thank you!!

Thanks for video, but where did u get the cover gasket ?

Hello thanks for your video a quick question would it be fine if I use cvt transmission fluid like valvoline for the flushes and then Nissan TF for final fill just curious if it would be an issue

My transmission pan got hit while driving down the road car only has 70000 miles would I need to flush 2 times or can I just go ahead and replace gasket and pan and add fluid thru overflow as you did thanks for your time

if anyone else is uncomfortable about the "feel it" torque spec: the upper, 8mm bolt (12mm head): 16ft lbs (22Nm) lower, 10mm bolt (14mm head): 33 ft lbs (45Nm) everything else he did was solid.

What about the wires, what order do they go in?

What was that plug in device you used with your phone? Where can I get one? Very nice video. How many quarts of cvt fluid will I need overall? Thanks again.

Good! But if transmission is low on fluid will make that noise(rare). Best to take it to the dealer because sound like is air on the transmission

The problem in many cars like Honda people think they are Philipps screws, they are not they are Japanese Industrial Standard (JIS) screws and you need to use a JIS screwdriver which is easy to get.

Sorry if this is a dumb question, but do I need to drain the oil first?

In my opinion: I would just soak the screw in Marvel Mystery Oil the night before & go for a drive to heat things up before using an impact gun. Heat always is a bad idea because it compromises grease, warps rubber seals & metal parts. It softens parts & annuals them shorting service life. Northern Yankees do dumb stuff like that just like how they pop off exhaust manifold bolts because someone used a torch on a previous repair. If it doesn't work, probably best to drill the head with the smallest bit passing through the inside of the screw & drill off the head. You can remove the rest with an easy out. Striking a bearing hub is always bad because it always spaulds the bearings. It's another reason not to let anyone else work on your breaks because they'd go for the impact driver first because it's the fastest thing.

Great video, very helpful thanks!

my car battery went dead while bleeding my brakes. After i finished the brake flush, i jumped the engine but then immediately the check engine light turned on. I went to autozone and code ABS malfunction and traction off showed up on dash. not knowing what to do, i removed the battery, check engine light turned off for now but for how long?

Brother you’re an amazing person and truly understand the basic person trying to not mess anything up. Truly appreciate your video and the quality more than anything!

Bro I'm elbow deep in this and I've dome all the same shit but one of the long bolts that's right under the pulley just goes all the way in with nothing to thread it too. I didn't strip it, I never got it to even start by finger. I've checked alignment and I'm in. I have 6 in and still nothing will even start to catch. Its a long bolt, I don't understand how it goes all the way in and catches nothing

So is there an actual Dip Stick for the Trans? Been looking for one for a while now?

This is how a HOW-TO should be done, steps, part numbers, FSM info, and some helpful commentary!

Yep I noticed the same drift on my 14 2.5 and I also replaced control arm with the beck although I'm not getting the balding of the tires ..

Rear starts 20:40

Awesome vid. This was about a 15 min job for me. Im def not a mechanic. Saved me over $100. Thank you!!

Honestly the best informational video I’ve seen on an vehicle! Great job man

Great video, thank you so much!

I just blew mine out with air

I have a 2019 Altima and I already had to replace my too because the rubber is already torn too. Nissan probably have a bad design or used cheap materials. LOL

Very informative video. I'm inspired to do this job myself. Thank you kindly sir.

such a helpful video. I’m lazy so just drained and refilled. Better than nothing. lol. Thanks for the tutorial😊

Holy shit this was so easy to follow. Great video! Wish you had one on changing the starter on this car.

That filter inside of the pan on the valve body is to filter out course metallic filings. If it looks pretty good and clean, it is unnecessary to change it. The paper cartridge is the most important to change for fine contaminates.

This is not a complete fluid change. 1/2 of the fluid is in the torque converter and valve body. To do a complete change, while the trans is hot and vehicle is running, you need to break into the trans cooling output and input lines. Using a pump, you put in as much as it comes out until it is clear new fluid. Do all of this then replace the filter behind the trans cooler. Then check with car level using the overflow drain plug removed. After fluid is drained, replace the overflow drain plug. You now have the proper level and have done a proper trans fluid change out.

Finally! A video that explains it all! What I needed! Thanks BeeCee!

FOR EVRYONE ! IF YOU CHANGED THE SERPENTINE BELT TO GATES OR NOT OEM IT'S THAT XD I KNOW YOU DONT BELIVE BUT IT IS

Hey bro, huge shout out to you. Just ordered all my stuff off rock auto gets here tomorrow. I took the old water pump off today ready to put a new one on tomorrow thanks to your video.

That clip isnt rubbing because rust build up. Look where your pads hook. I bet they're wearing a grove in the carrier.

Good afternoon, greetings, thank you for this video. Exactly the same thing happened to me in my Ford Explorer and I was able to solve it just as you did in my case. The fuse was broken. I changed it and that's it. It worked 100%.

Hi watch this before doin mine so I remove about 4 quarts then when I open the overflow plug and I remove a little bit over half a quart and the drip still going so I just put the plug back? Should I put back the half quart I removed?

Did you ever change the filters? Great video

I bought the same brand you did but the alternator won’t budge into place

Diag/signs of bad alternator: Battery light comes on. Check volts on the battery and on the alternator with a voltmeter. Good battery should be 12.5 V car off and cold, 13.7-14.7 V while running, alternator should match battery V. If V are good from alternator but not the battery it is probably a bad battery. Car won’t start. Check volts on battery and on alternator with a voltmeter Check serpentine belt to make sure it is connected Check computer for codes Procedure to replace alternator -Remove battery connections (negative first, then positive, make sure the connections are clear) -Remove coolant reservoir to make space -move power steering fluid reservoir but do not remove -loosen the tensioner pulley to pull the serpentine/drive belt off the alternator - remove wiring harness (push tab in and pull to unplug) -remove 2-3 bolts (depends on year) that are keeping alternator in position (you can use a magnet to catch bolts, or hand loosen -Now the alternator will move, remove bolt from from the positive cable wire -Install new alternator in reverse order and replace items that you removed. Ensure serpentine belt is on correctly -Test new alternator and battery voltages

How much should I be paying for a brake job on my 17

FYI any digital odometer can be digitally programmed to whatever number you just have to have the correct OBD plug device

Hi I have tight power steering and dealer is suggesting to replace rack and pinion besides the control arms tie rods for 5k. Which by itself is crazy expensive but you think I shouldn’t just try trepkacing the control arms and see if it fixes things?

Great video.

A really great 👍 job. Your video is one of the best I've ever seen on doing a repair. Very detailed and informative. Thank you.

I've twisted off two torx tools, one adapted to a hand impact tool, after heated. Next step, Drill baby, drill! I've heard rotors can shatter if hit with a hammer, so glad to see you used a soft face hammer. Thanks for tip on they are not necessary to reinstall. That was my suspicion.

Thanks!

Thank you for the video, I will be watching it as I give this a try, it will be my first time every doing a transmission fluid change. I have 2014 NIssan Altima with a little over 135K - it's going to be the 1st transmission fluid change. Again, thank you for such an excellent video!!

Excellent video. Thank you

Thanks for this tutorial, I have a Kia Cerato Forte 2010 model, that carries a rear drum brake assembly. I want to change that system out and install a rotor disc brake assembly. What do I have to get to do the conversion. The reason I ask and want to do the conversion, where I'm from the drum is obsolete.

Thank you bro from México city 🙏 this is my problem in my ranger 94